Channel Screed Vent Panel

Channel Screed Vent Panel

Flannery's Channel Screed Vent Panels are an excellent tool for ventilating soffits or attic spaces. Vent Panels are ideal for drawing cooler air into the attic forcing warm or stale air to be exhausted through ridge, gable, and turbine vents.

Many "do-it-yourself" stores sell aluminum vents that are as thin as a soda can which can easily be chewed through or damaged. All of Flannery's Vent Panels have .050" thick walls, which makes them some of the sturdiest vent panels on the market. Since Vent Panels contain vent slots (1" x 1/8") and not holes, bees, wasps, and many other insects cannot fly or crawl through the vent slots.

While many screen vents and other steel vents will eventually rust out, Flannery's Vent Panels will never rust out since they are manufactured from extruded aluminum. Flannery manufactures various sizes and lengths Channel Screed Vent Panels.

Manufacturer's Specification

Channel Screed Vent Panels are standard extruded aluminum alloy 6063 T5 and are .050" thick. Channel Screed Vent Panels shall have a standard Clear Anodized finish. Mill and Alodine (Chemfilm) finishes as well as other factory finishes and custom paint orders are available. Refer to Finishes for details.

Install all Channel Screed Vent Panels to the framing with nails, screws, or other approved fastening methods. All nailing flanges must be covered with lath material before stucco cement is applied. Vent Area and Reveal must be protected (masked or taped) before plaster cement is applied to the soffit. Protection must not be removed until stucco finish is completed. 

For Material Safety Data Sheet (MSDS Report), click here. 

 

 

 

 

Part No.	"A"  Reveal  Width	"B" Overall Width	"C"  Overall Height
PCS 375-VP-50	1/2"	2.35"	1/2"
PCS 375-VP-75	3/4"	2.60"	1/2"
PCS 375-VP-100	1"	2.85"	1/2"
PCS 375-VP-150	1 1/2"	3.35"	1/2"
PCS 50-VP-50	1/2"	2.35"	5/8"
PCS 50-VP-75	3/4"	2.60"	5/8"
PCS 50-VP-100	1"	2.85"	5/8"
PCS 50-VP-150	1 1/2"	3.35"	5/8"
PCS 50-VP-200	2"	3.85"	5/8"
PCS 50-VP-250	2 1/2"	4.35"	5/8"
PCS 50-VP-300	3"	4.85"	5/8"
PCS 50-VP-400	4"	5.85"	5/8"
PCS 50-VP-600	6"	7.85"	5/8"
PCS 625-VP-50	1/2"	2.35"	3/4"
PCS 625-VP-75	3/4"	2.60"	3/4"
PCS 625-VP-100	1"	2.85"	3/4"
PCS 625-VP-150	1 1/2"	3.35"	3/4"
PCS 625-VP-200	2"	3.85"	3/4"
PCS 625-VP-300	3"	4.85"	3/4"
PCS 625-VP-400	4"	5.85"	3/4"
PCS 75-VP-50	1/2"	2.35"	7/8"
PCS 75-VP-75	3/4"	2.60"	7/8"
PCS 75-VP-100	1"	2.85"	7/8"
PCS 75-VP-150	1 1/2"	3.35"	7/8"
PCS 75-VP-200	2"	3.85"	7/8"
PCS 75-VP-250	2 1/2"	4.35"	7/8"
PCS 75-VP-300	3"	4.85"	7/8"
PCS 75-VP-400	4"	5.85"	7/8"
PCS 75-VP-600	6"	7.85"	7/8"

 

 

 

 Vent Area Graph 

Reveal Width	Vent Slots	Vent Area Per Lineal Foot Approx
1/2"	1	1 sq. inch
3/4"	1	1 sq. inch
7/8"	1	1 sq. inch
1"	1	1 sq. inch
1 1/2"	2	2 sq. inch
2"	3	3 sq. inch
2 1/2"	3	3 sq. inch
3"	5	5 sq. inch
4"	7	7 sq. inch
6"	8	8 sq. inch

 

 

 

Installation Detail- Side View

 

 

Installation Detail- Frontal View 

 

Installation Detail- Angled View with Finish

 

Angled View Zoomed In

 

 

 

 

 

 

This website presents general guidelines and suggestions for the installation of Flannery trims and products. The purpose of these general guidelines and suggestions is to aid in a successful drywall or stucco finish based on the Uniform Building Code and industry standards. No website or catalog can address all of the unique specifics or installation details that occur from one project to another. Flannery recommends that every installer be familiar, or become acquainted with, common drywall and stucco trim installation practices before installing any of Flannery's many trims and products. Flannery also recommends that the specifying architect, engineer, and general contractor be consulted with as well. This website replaces and renders obsolete all previous publications by Flannery; including catalogs, pamphlets, or other forms of literature.