C. T Mold Vent
Click on large image to see full sized
T Mold with Vent
Manufacturer's Specifications
Many of the sizes that Flannery offers of our T Molds are available with Vent Slots. All Vent Slots are 1/8” wide and 1” long. They are configured at 1½” on center lengthwise and ½” on center laterally. Each row of Vent Slots lengthwise provides approximately one-square inch of vented area per lineal foot (see Vent Area Graph below).
T Molds with Vent must not be installed in areas where there is solid framing, since this may block some or possibly all of the vent slots. Attach T Mold Vents to the framing with nails, screws, or other approved fastening methods. To ease installation, Flannery offers Aluminum Alignment Splices for most of its Vent Screeds. All T Molds with Vent must be cut accurately and installed with tight, neat joints. All nailing flanges must be covered with lath and all butt joints must be sealed. Manufacturer recommends that a carbide tip blade along with lubricant be used when cutting any aluminum trims. Please specify Flannery Product Code along with the phrase "with Vent" (i.e. TPM 75-200 with Vent" or TPM 75-V-200) when ordering T Molds with Vent slots.
For a Material Safety Data Sheet (MSDS report), click here.
|
Part No. |
"A" Depth |
"B" Width |
Alignment Splices |
Venting Available |
| TPM 375-V-50* | 3/8" | 1/2" | N/A | Yes |
| TPM 375-V-75* | 3/8" | 3/4" | N/A | Yes |
| TPM 375-V-100* | 3/8" | 1" | N/A | Yes |
| TPM 375-V-150* | 3/8" | 1 1/2" | N/A | Yes |
| TPM 50-V-50* | 1/2" | 1/2" | N/A | Yes |
| TPM 50-V-75* | 1/2" | 3/4" | N/A | Yes |
| TPM 50-V-100* | 1/2" | 1" | N/A | Yes |
| TPM 50-V-150* | 1/2" | 1 1/2" | N/A | Yes |
| TPM 50-V-200* | 1/2" | 2" | N/A | Yes |
| TPM 50-V-300* | 1/2" | 3" | N/A | Yes |
| TPM 50-V-400* | 1/2" | 4" | N/A | Yes |
| TPM 50-V-600* | 1/2" | 6" | N/A | Yes |
| TPM 625-V-50* | 5/8" | 1/2" | N/A | Yes |
| TPM 625-V-75 | 5/8" | 3/4" | N/A | Yes |
| TPM 625-V-100* | 5/8" | 1" | N/A | Yes |
| TPM 625-V-150* | 5/8" | 1 1/2" | N/A | Yes |
| TPM 625-V-200* | 5/8" | 2" | N/A | Yes |
| TPM 625-V-300* | 5/8" | 3" | N/A | Yes |
| TPM 625-V-400* | 5/8" | 4" | N/A | Yes |
| TPM 75-V-50* | 3/4" | 1/2" | Yes | Yes |
| TPM 75-V-75 | 3/4" | 3/4" | N/A | Yes |
| TPM 75-V-100* | 3/4" | 1" | N/A | Yes |
| TPM 75-V-150 | 3/4" | 1 1/2" | N/A | Yes |
| TPM 75-V-200* | 3/4" | 2" | N/A | Yes |
| TPM 75-V-250* | 3/4" | 2 1/2" | N/A | Yes |
| TPM 75-V-300* | 3/4" | 3" | Yes | Yes |
| TPM 75-V-400* | 3/4" | 4" | N/A | Yes |
| TPM 75-V-600* | 3/4" | 6" | N/A | Yes |
| Reveal Width | Vent Slots | Vent Area Per Lineal Foot Approx |
| 1/2" | 1 | 1 sq. inch |
| 3/4" | 1 | 1 sq. inch |
| 7/8" | 1 | 1 sq. inch |
| 1" | 1 | 1 sq. inch |
| 1 1/2" | 2 | 2 sq. inch |
| 2" | 3 | 3 sq. inch |
| 2 1/2" | 3 | 3 sq. inch |
| 3" | 5 | 5 sq. inch |
| 4" | 7 | 7 sq. inch |
| 6" | 8 | 8 sq. inch |
* Indicates Modified Part, No Returns.
Installation Detail
This website presents general guidelines and suggestions for the installation of Flannery trims and products. The purpose of these general guidelines and suggestions is to aid in a successful drywall or stucco finish based on the Uniform Building Code and industry standards. No website or catalog can address all of the unique specifics or installation details that occur from one project to another. Flannery recommends that every installer be familiar, or become acquainted with, common drywall and stucco trim installation practices before installing any of Flannery\\\\'s many trims and products. Flannery also recommends that the specifying architect, engineer, and general contractor be consulted with as well. This website replaces and renders obsolete all previous publications by Flannery; including catalogs, pamphlets, or other forms of literature.
300 Parkside Drive | San Fernando, California 91340 | Tel. (818) 837-7585 | Fax. (818) 837-1155 | Email. info@flannerytrim.com
Copyright © 2010 by Flannery Trim |
Designed by 
Point One Media Inc.