T Mold

DWG Files

Manufacturer's Specification

T Molds are standard extruded aluminum alloy 6063 T5 and are .050 thick. T Molds shall have a standard Clear Anodized finish. Mill and Alodine finishes as well as other factory finishes and custom paint orders are available. Refer to Finishes for details. Click the Venting Options link  for venting options.

Install all T Molds using full ten-foot lengths wherever possible. Attach T Molds to the framing with nails, screws, or other approved fastening methods. All T Molds must be cut accurately and installed with tight, neat joints. All nailing flanges must be covered with lath and all butt joints must be sealed. Manufacturer recommends that a carbide tip blade along with lubricant be used when cutting any aluminum trims.

For MSDS report, click "More Information (PDF)" above.

Channel Alignment Splices

Flannery is the first manufacturer to offer splices for   T Molds. Various sizes of Flannery’s T Molds are now available with Alignment Splices. Alignment Splices are suitable for butt joints, corners, and radius work. Refer Alignment Splices product information for details.

Part No.	"A" Depth	"B" Width	Alignment Splices	Venting Available
TPM 375-50*	3/8"	1/2"	N/A	Yes
TPM 375-75*	3/8"	3/4"	N/A	Yes
TPM 375-100*	3/8"	1"	N/A	Yes
TPM 375-150*	3/8"	1 1/2"	N/A	Yes
TPM 50-50*	1/2"	1/2"	N/A	Yes
TPM 50-75*	1/2"	3/4"	N/A	Yes
TPM 50-100*	1/2"	1"	N/A	Yes
TPM 50-150*	1/2"	1 1/2"	N/A	Yes
TPM 50-200*	1/2"	2"	N/A	Yes
TPM 50-300*	1/2"	3"	N/A	Yes
TPM 50-400*	1/2"	4"	N/A	Yes
TPM 50-600*	1/2"	6"	N/A	Yes
TPM 625-50*	5/8"	1/2"	N/A	Yes
TPM 625-75	5/8"	3/4"	N/A	Yes
TPM 625-100*	5/8"	1"	N/A	Yes
TPM 625-150*	5/8"	1 1/2"	N/A	Yes
TPM 625-200*	5/8"	2"	N/A	Yes
TPM 625-300*	5/8"	3"	N/A	Yes
TPM 625-400*	5/8"	4"	N/A	Yes
TPM 75-50*	3/4"	1/2"	Yes	Yes
TPM 75-75	3/4"	3/4"	N/A	Yes
TPM 75-100*	3/4"	1"	N/A	Yes
TPM 75-150	3/4"	1 1/2"	N/A	Yes
TPM 75-200*	3/4"	2"	N/A	Yes
TPM 75-250*	3/4"	2 1/2"	N/A	Yes
TPM 75-300*	3/4"	3"	Yes	Yes
TPM 75-400*	3/4"	4"	N/A	Yes
TPM 75-600*	3/4"	6"	N/A	Yes

 * Indicates Modified Part, No Returns.

Installation Detail

T Mold with Vent Slots (Click Here)

Intersections & Corners

Radius Shapes

This website presents general guidelines and suggestions for the installation of Flannery trims and products. The purpose of these general guidelines and suggestions is to aid in a successful drywall or stucco finish based on the Uniform Building Code and industry standards. No website or catalog can address all of the unique specifics or installation details that occur from one project to another. Flannery recommends that every installer be familiar, or become acquainted with, common drywall and stucco trim installation practices before installing any of Flannery's many trims and products. Flannery also recommends that the specifying architect, engineer, and general contractor be consulted with as well. This website replaces and renders obsolete all previous publications by Flannery; including catalogs, pamphlets, or other forms of literature.