Plaster T-Mold

Trim Purpose

Specs, MSDS, and LEED Information for Flannery Trims & Products

Flannery’s T-Mold creates an aesthetic termination trim with a reveal wherever you wish to terminate stucco, veneer plaster, drywall or wood panels. Typically installed where a stucco wall terminates at an opposing wall or dissimilar material, Flannery’s T-Mold can act as a stucco stop with a built in reveal.

Product Details

Flannery’s Aluminum Termination Trims are standard extruded aluminum alloy 6063 T5 and have a .050” nominal wall thickness. Termination Trims come in 10′ lengths and shall have a standard Clear Anodized Finish. Mill Finish (for field priming & painting), Chem-film finish or other factory finishes and custom paint orders are available. You can view our factory finishes to see if we have what you are looking for or if you do not see the finish, you are looking for, chances are we can color-match it or we already have it! Flannery Trim wants to always make sure we can get you the right look and feel for your building project.

This product is also known in the industry as a TRM and TDM.


Product Number “A” Depth “B” Width Stucco Thickness Stock Item Venting Available
TPM 375-50* 3/8″ 1/2″ 1/2″ No Yes
TPM 375-75* 3/8″ 3/4″ 1/2″ No Yes
TPM 375-100* 3/8″ 1″ 1/2″ No Yes
TPM 375-150* 3/8″ 1 1/2″ 1/2″ No Yes
TPM 50-50* 1/2″ 1/2″ 5/8″ No Yes
TPM 50-75* 1/2″ 3/4″ 5/8″ No Yes
TPM 50-100* 1/2″ 1″ 5/8″ No Yes
TPM 50-150* 1/2″ 1 1/2″ 5/8″ No Yes
TPM 50-200* 1/2″ 2″ 5/8″ No Yes
TPM 50-250* 1/2″ 2 1/2″ 5/8″ No Yes
TPM 50-300* 1/2″ 3″ 5/8″ No Yes
TPM 50-400* 1/2″ 4″ 5/8″ No Yes
TPM 50-600* 1/2″ 6″ 5/8″ No Yes
TPM 625-50* 5/8″ 1/2″ 3/4″ No Yes
TPM 625-75 5/8″ 3/4″ 3/4″ Yes Yes
TPM 625-100* 5/8″ 1″ 3/4″ No Yes
TPM 625-150* 5/8″ 1 1/2″ 3/4″ No Yes
TPM 625-200* 5/8″ 2″ 3/4″ No Yes
TPM 625-300* 5/8″ 3″ 3/4″ No Yes
TPM 625-400* 5/8″ 4″ 3/4″ No Yes
TPM 75-50* 3/4″ 1/2″ 7/8″ No Yes
TPM 75-75 3/4″ 3/4″ 7/8″ Yes Yes
TPM 75-100* 3/4″ 1″ 7/8″ No Yes
TPM 75-150 3/4″ 1 1/2″ 7/8″ Yes Yes
TPM 75-200* 3/4″ 2″ 7/8″ No Yes
TPM 75-250* 3/4″ 2 1/2″ 7/8″ No Yes
TPM 75-300* 3/4″ 3″ 7/8″ No Yes
TPM 75-400* 3/4″ 4″ 7/8″ No Yes
TPM 75-600* 3/4″ 6″ 7/8″ No Yes

 

Install all T-Molds using full ten-foot lengths wherever possible. All Aluminum Trims must be cut accurately and installed with tight, neat joints. Manufacturer recommends that a carbide tip blade along with lubricant be used when cutting any aluminum trims.

If used in a stucco wall system, attach all Termination Trims over the weather resistant barrier (WRB) to the framing with nails, screws, or other approved fastening methods. A shiplap of building paper or WRB may need to be installed over the attachment flange if the trims are being used as a stucco stop. All nailing flanges must be covered with lath and all butt joints must be sealed.


Flannery offers prefabricated corners for intricate building designs that utilize intersecting lines and bands on exterior walls. Prefabricated corners are mitered and then welded together at their attachment flanges, then vinyl tape is applied to the back of the reveal to prevent water intrusion. Factory welded corners come with 6” legs, however custom leg lengths can be ordered.


Flannery can radius Plaster T-Molds when the trim runs along a “curved” or “radiused” plane. Radiused material is bent to a project’s dimensional requirements and is considered a custom product. Download the Radius Form or view all of our radius forms.


You may also like…

  • Plaster F-Mold

  • Soffit W-Mold

  • Plaster T-Mold Vent

  • Plaster J-Mold